 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| ICX204AK Diagonal 6mm (Type 1/3) Progressive Scan CCD Image Sensor with Square Pixel for Color Cameras Description The ICX204AK is a diagonal 6mm (Type 1/3) interline CCD solid-state image sensor with a square pixel array and 800K effective pixels. Progressive scan allows all pixels' signals to be output independently. Also, the adoption of high frame rate readout mode supports 60 frames per second. This chip features an electronic shutter with variable charge-storage time which makes it possible to realize full-frame still image without a mechanical shutter. High resolution and high color reproductivity are achieved through the use of R, G, B primary color mosaic filters. Further, high sensitivity and low dark current are achieved through the adoption of HAD (Hole-Accumulation Diode) sensors. This chip is suitable for applications such as electronic still cameras, PC input cameras, etc. Features * Progressive scan allows individual readout of the image signals from all pixels. * High horizontal and vertical resolution (both approx. 600TV-lines) still image without a mechanical shutter. * Supports high frame rate readout mode (effective 256 lines output, 15MHz drive: 45 frame/s, 20MHz drive: 60 frame/s) * Square pixel * Horizontal drive frequency: Typ.: 15MHz, Max.: 20MHz * No voltage adjustments (reset gate and substrate bias are not adjusted.) * R, G, B primary color mosaic filters on chip * High resolution, high color reproductivity, high sensitivity, low dark current * Low smear, excellent antiblooming characteristics * Continuous variable-speed shutter * Recommended range of exit pupil distance: -20 to -100mm Device Structure * Interline CCD image sensor * Image size: * Total number of pixels: * Number of effective pixels: * Number of active pixels: * Chip size: * Unit cell size: * Optical black: * Number of dummy bits: * Substrate material: 16 pin DIP (Plastic) Pin 1 2 V 7 3 Pin 9 H 40 Optical black position (Top View) Diagonal 6mm (Type 1/3) 1077 (H) x 788 (V) approx. 850K pixels 1034 (H) x 779 (V) approx. 800K pixels 1024 (H) x 768 (V) approx. 790K pixels (diagonal 5.952mm) 5.80mm (H) x 4.92mm (V) 4.65m (H) x 4.65m (V) Horizontal (H) direction: Front 3 pixels, rear 40 pixels Vertical (V) direction: Front 7 pixels, rear 2 pixels Horizontal 29 Vertical 1 Silicon Wfine CCD is a registered trademark of Sony Corporation. Represents a CCD adopting progressive scan, primary color filter and square pixel. Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits. -1- E97X05B99 ICX204AK Block Diagram and Pin Configuration (Top View) VOUT GND V2A V2B 2 G B G B G B G NC NC 8 7 6 5 V1 4 3 1 R G B G B G B G R G R G R G R Vertical register G R G R G R Horizontal register Note) 9 10 11 12 13 14 15 16 : Photo sensor Pin Description Pin No. 1 2 3 4 5 6 7 8 Symbol V3 V2B V1 V2A GND NC NC VOUT Signal output Description Vertical register transfer clock Vertical register transfer clock Vertical register transfer clock Vertical register transfer clock GND Pin No. 9 10 11 12 13 14 15 16 Symbol VDD GND SUB CSUB VL RG H1 H2 Description Supply voltage GND Substrate clock Substrate bias1 Protective transistor bias Reset gate clock Horizontal register transfer clock Horizontal register transfer clock 1 DC bias is generated within the CCD, so that this pin should be grounded externally through a capacitance of 0.1F. SUB CSUB GND -2- RG VDD H2 H1 VL V3 Note) ICX204AK Absolute Maximum Ratings Item VDD, VOUT, RG - SUB V2A, V2B - SUB Against SUB V1, V3, VL - SUB H1, H2, GND - SUB CSUB - SUB VDD, VOUT, RG, CSUB - GND Against GND V1, V2A, V2B, V3 - GND H1, H2 - GND Against VL V2A, V2B - VL V1, V3, H1, H2, GND - VL Voltage difference between vertical clock input pins Between input clock pins H1 - H2 H1, H2 - V3 Storage temperature Operating temperature 2 +24V (Max.) when clock width < 10s, clock duty factor < 0.1%. +16V (Max.) is guaranteed for turning on or off power supply. Ratings -40 to +10 -50 to +15 -50 to +0.3 -40 to +0.3 -25 to -0.3 to +18 -10 to +18 -10 to +5 -0.3 to +28 -0.3 to +15 to +15 -5 to +5 -13 to +13 -30 to +80 -10 to +60 Unit Remarks V V V V V V V V V V V V V C C 2 -3- ICX204AK Bias Conditions Item Supply voltage Protective transistor bias Substrate clock Reset gate clock Symbol VDD VL SUB RG Min. 14.55 Typ. 15.0 1 2 2 Max. 15.45 Unit V Remarks 1 VL setting is the VVL voltage of the vertical transfer clock waveform, or the same power supply as the VL power supply for the V driver should be used. 2 Do not apply a DC bias to the substrate clock and reset gate clock pins, because a DC bias is generated within the CCD. DC Characteristics Item Supply current Symbol IDD Min. Typ. 5.5 Max. Unit mA Remarks Clock Voltage Conditions Item Readout clock voltage VVT VVH02A VVH1, VVH2A, VVH2B, VVH3 VVL1, VVL2A, VVL2B, VVL3 Vertical transfer clock voltage V1, V2A, V2B, V3 | VVL1 - VVL3 | VVHH VVHL VVLH VVLL Horizontal transfer clock voltage Reset gate clock voltage VH VHL VRG VRGLH - VRGLL VRGL - VRGLm Substrate clock voltage VSUB 21.55 22.5 3.0 -0.05 3.0 3.3 0 3.3 Symbol Min. 14.55 -0.05 -0.2 -8 7 Typ. 15.0 0 0 -7.5 7.5 Max. 15.45 0.05 0.05 -7 8 0.1 0.9 1.3 1.0 0.9 3.6 0.05 3.6 0.4 0.5 23.45 Unit V V V V V V V V V V V V V V V V Waveform diagram 1 2 2 2 2 2 2 2 2 2 3 3 4 4 4 5 Low-level coupling Low-level coupling High-level coupling High-level coupling Low-level coupling Low-level coupling VVL = (VVL1 + VVL3)/2 VVH = VVH02A Remarks -4- ICX204AK Clock Equivalent Circuit Constant Item Symbol CV1 Capacitance between vertical transfer clock and GND CV2A CV2B CV3 CV12A CV2B1 Capacitance between vertical transfer clocks CV2A3 CV32B CV13 CV2A2B Capacitance between horizontal transfer clock and GND Capacitance between horizontal transfer clocks Capacitance between reset gate clock and GND Capacitance between substrate clock and GND CH1, CH2 CHH CRG CSUB R1 R2A Vertical transfer clock series resistor R2B R3 Vertical transfer clock ground resistor Horizontal transfer clock series resistor RGND RH Min. Typ. 1500 1800 2700 2200 390 680 560 1000 1800 33 18 43 3 390 91 68 62 30 43 10 Max. Unit pF pF pF pF pF pF pF pF pF pF pF pF pF pF Remarks V1 CV12A V2A R1 R2A RH H1 RH H2 CHH CV2A3 CV13 CH1 CH2 CV1 CV2B1 CV2A2B CV2A CV2B RGND CV3 R2B CV32B R3 V2B V3 Vertical transfer clock equivalent circuit Horizontal transfer clock equivalent circuit -5- ICX204AK Drive Clock Waveform Conditions (1) Readout clock waveform VT 100% 90% II II M M 2 0V VVT 10% 0% tr twh tf Note) Readout clock is used by composing vertical transfer clocks V2A and V2B. (2) Vertical transfer clock waveform V1 VVHL VVH1 VVHH VVH VVLH VVL01 VVL1 VVLL V2A, V2B VVH02A, VVH02B VVHH VVHL VVH2A, VVH2B VVH VVL VVLH VVL2A, VVL2B VVLL V3 VVHL VVH3 VVHH VVH VVL VVL03 VVLL VVLH VVL VVH = VVH02A VVL = (VVL01 + VVL03) / 2 VVL3 = VVL03 -6- VV1 = VVH1 - VVL01 VV2A = VVH02A - VVL2A VV2B = VVH02B - VVL2B VV3 = VVH3 - VVL03 ICX204AK (3) Horizontal transfer clock waveform tr H2 90% VCR VH 10% H1 two VH 2 twl twh tf VHL Cross-point voltage for the H1 rising side of the horizontal transfer clocks H1 and H2 waveforms is VCR. The overlap period for twh and twl of horizontal transfer clocks H1 and H2 is two. (4) Reset gate clock waveform tr twh tf RG waveform VRGH twl VRG Point A VRGLH VRGLL VRGLm VRGL VRGLH is the maximum value and VRGLL is the minimum value of the coupling waveform during the period from Point A in the above diagram until the rising edge of RG. In addition, VRGL is the average value of VRGLH and VRGLL. VRGL = (VRGLH + VRGLL)/2 Assuming VRGH is the minimum value during the interval twh, then: VRG = VRGH - VRGL. Negative overshoot level during the falling edge of RG is VRGLm. (5) Substrate clock waveform 100% 90% M VSUB 10% VSUB 0% (A bias generated within the CCD) M 2 tf tr twh -7- ICX204AK Clock Switching Characteristics Item Readout clock Vertical transfer clock Horizontal transfer clock Symbol VT V1, V2A, V2B, V3 H1 H2 twh twl tr tf Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. 2.3 2.5 0.5 15 12.5 17 12.5 17 12.5 17 12.5 17 8.2 8.2 7 10 2.2 34 8 8 0.01 0.01 3 0.5 12.5 12.5 8 8 0.01 0.01 3 0.5 Unit Remarks s During readout 350 ns 12.5 12.5 ns 1 2 During imaging During H1 parallel-serial H2 conversion RG SUB s ns 0.5 s During drain charge Reset gate clock Substrate clock 1 When vertical transfer clock driver CXD1267AN is used. 2 tf tr - 2ns, and the cross-point voltage (VCR) for the H1 rising side of the H1 and H2 waveforms must be at least VH/2 [V]. two Item Horizontal transfer clock Symbol Min. Typ. Max. Unit ns Remarks H1, H2 10.5 17 Spectral Sensitivity Characteristics (excludes lens characteristics and light source characteristics) 1 G 0.8 B R Relative Response 0.6 0.4 0.2 0 400 500 Wave Length [nm] 600 700 -8- ICX204AK Image Sensor Characteristics Item G sensitivity Sensitivity comparison Saturation signal Smear Video signal shading Uniformity between video signal channels Dark signal Dark signal shading Line crawl G Line crawl R Line crawl B Lag R B Symbol Sg Rr Rb Vsat Sm SHg Srg Sbg Vdt Vdt Lcg Lcr Lcb Lag Min. 320 0.4 0.3 450 0.001 0.004 20 25 8 8 6 2 3.8 3.8 3.8 0.5 Typ. 400 0.55 0.45 0.7 0.6 mV % % % % % mV mV % % % % Max. Unit mV Measurement method 1 1 1 2 3 4 4 5 5 6 7 8 8 8 9 Ta = 60C (Ta = 25C) Remarks 1/30s accumulation No electronic shutter Zone 0 and I Zone 0 to II' Ta = 60C, 20 frame/s Ta = 60C, 20 frame/s Zone Definition of Video Signal Shading 1034 (H) 4 4 4 H 8 V 10 H 8 779 (V) Zone 0, I Zone II, II' V 10 5 Ignored region Effective pixel region Measurement System CCD signal output [A] Gr/Gb CCD C.D.S AMP S/H R/B S/H R/B channel signal output [C] Gr/Gb channel signal output [B] Note) Adjust the amplifier gain so that the gain between [A] and [B], and between [A] and [C] equals 1. -9- ICX204AK Image Sensor Characteristics Measurement Method Color coding and readout of this image sensor Gb R Gb R B Gr B Gr Gb R Gb R B Gr B Gr The primary color filters of this image sensor are arranged in the layout shown in the figure on the left (Bayer arrangement). Gr and Gb denote the G signals on the same line as the R signal and the B signal, respectively. Horizontal register Color Coding Diagram All pixel signals are output successively in a 1/20s period. The R signal and Gr signal lines and the Gb signal and B signal lines are output successively. - 10 - ICX204AK Readout modes The diagram below shows the output methods for the following two readout modes. Progressive scan mode 12 11 10 9 8 7 6 5 4 3 2 1 VOUT G R G R G R G R G R G R B G B G B G B G B G B G VOUT High frame rate readout mode 12 11 10 9 8 7 6 5 4 3 2 1 G R G R G R G R G R G R B G B G B G B G B G B G Note) Blacked out portions in the diagram indicate pixels which are not read out. Output starts from the line 7 in high frame rate readout mode. 1. Progressive scan mode In this mode, all pixel signals are output in non-interlace format in 1/20s. The vertical resolution is approximately 600TV-lines and all pixel signals within the same exposure period are read out simultaneously, making this mode suitable for high resolution image capturing. 2. High frame rate readout mode All effective areas are scanned in approximately 1/60s by reading out one line for every three lines. The vertical resolution is approximately 200TV-lines. This readout mode emphasizes processing speed over vertical resolution. - 11 - ICX204AK Measurement conditions 1) In the following measurements, the device drive conditions are at the typical values of the progressive scan mode, bias and clock voltage conditions. 2) In the following measurements, spot blemishes are excluded and, unless otherwise specified, the optical black level (OB) is used as the reference for the signal output, which is taken as the value of the Gr/Gb signal output or the R/B signal output of the measurement system. Definition of standard imaging conditions 1) Standard imaging condition I: Use a pattern box (luminance: 706cd/m2, color temperature of 3200K halogen source) as a subject. (Pattern for evaluation is not applicable.) Use a testing standard lens with CM500S (t = 1.0mm) as an IR cut filter and image at F5.6. The luminous intensity to the sensor receiving surface at this point is defined as the standard sensitivity testing luminous intensity. 2) Standard imaging condition II: Image a light source (color temperature of 3200K) with a uniformity of brightness within 2% at all angles. Use a testing standard lens with CM500S (t = 1.0mm) as an IR cut filter. The luminous intensity is adjusted to the value indicated in each testing item by the lens diaphragm. 3) Standard imaging condition III: Image a light source (color temperature of 3200K) with a uniformity of brightness within 2% at all angles. Use a testing standard lens (exit pupil distance -33mm) with CM500S (t = 1.0mm) as an IR cut filter. The luminous intensity is adjusted to the value indicated in each testing item by the lens diaphragm. 1. G sensitivity, sensitivity comparison Set to standard imaging condition I. After selecting the electronic shutter mode with a shutter speed of 1/100s, measure the signal outputs (VGr, VGb, VR and VB) at the center of each Gr, Gb, R and B channel screen, and substitute the values into the following formulas. VG = (VGr + VGb)/2 Sg = VG x 100/30 [mV] Rr = VR/VG Rb = VB/VG 2. Saturation signal Set to standard imaging condition II. After adjusting the luminous intensity to 20 times the intensity with the average value of the Gr signal output, 150mV, measure the minimum values of the Gr, Gb, R and B signal outputs. 3. Smear Set to standard imaging condition II. With the lens diaphragm at F5.6 to F8, first adjust the average value of the Gr signal output to 150mV. Measure the average values of the Gr signal output, Gb signal output, R signal output and B signal output (Gra, Gba, Ra, Ba), and then adjust the luminous intensity to 500 times the intensity with the average value of the Gr signal output, 150mV. After the readout clock is stopped and the charge drain is executed by the electronic shutter at the respective H blankings, measure the maximum value (VSm [mV]) independent of the Gr, Gb, R and B signal outputs, and substitute the values into the following formula. Sm = Vsm / Gra + Gba + Ra + Ba 4 x 1 1 x x 100 [%] (1/10V method conversion value) 10 500 - 12 - ICX204AK 4. Video signal shading Set to standard imaging condition III. With the lens diaphragm at F5.6 to F8, adjust the luminous intensity so that the average value of the Gr signal output is 150mV. Then measure the maximum (Grmax [mV]) and minimum (Grmin [mV]) values of the Gr signal output and substitute the values into the following formula. SHg = (Grmax - Grmin)/150 x 100 [%] 5. Uniformity between video signal channels After measuring 4, measure the maximum (Rmax [mV]) and minimum (Rmin [mV]) values of the R signal and the maximum (Bmax [mV]) and minimum (Bmin [mV]) values of the B signal, and substitute the values into the following formulas. Srg = (Rmax - Rmin)/150 x 100 [%] Sbg = (Bmax - Bmin)/150 x 100 [%] 6. Dark signal Measure the average value of the signal output (Vdt [mV]) with the device ambient temperature 60C and the device in the light-obstructed state, using the horizontal idle transfer level as a reference. 7. Dark signal shading After measuring 6, measure the maximum (Vdmax [mV]) and minimum (Vdmin [mV]) values of the dark signal output and substitute the values into the following formula. Vdt = Vdmax - Vdmin [mV] 8. Line crawl Set to standard imaging condition II. Adjusting the luminous intensity so that the average value of the Gr signal output is 150mV, and then insert R, G and B filters and measure the difference between G signal lines (Glr, Glg, Glb [mV]) as well as the average value of the G signal output (Gar, Gag, Gab). Substitute the values into the following formula. Lci = Gli/Gai x 100 [%] (i = r, g, b) 9. Lag Adjust the Gr signal output value generated by strobe light to 150mV. After setting the strobe light so that it strobes with the following timing, measure the residual signal (Vlag). Substitute the value into the following formula. Lag = (Vlag/150) x 100 [%] VD V2A Light Strobe light timing Gr signal output 150mV Vlag (lag) Output - 13 - Drive Circuit 15V 1 100k 2 3 1/35V -7.5V 4 5 CXD1267AN 15 14 13 12 11 1 2 3 7 4 8 5 6 22/16V 47 2SK1875 6 7 8 9 10 16 17 18 19 20 22/20V XSUB XV1 XV2A XSG1 XV2B XSG2 XV3 V3 V1 V2A NC NC V2B GND ICX204 (BOTTOM VIEW) VOUT H2 RG VL CSUB SUB GND H1 VDD - 14 - 16 15 14 13 12 11 10 9 0.1 0.1 2200p 3.3/16V 1M CCD OUT 1.8k 3.3/20V 0.01 H2 0.1 H1 RG ICX204AK Sensor Readout Clock Timing Chart Progressive Scan Mode XV1 XV2A/XV2B XV3 XSG1/XSG2 Sensor readout clocks XSG1 and XSG2 are used by composing XV2A and XV2B. - 15 - 0.1s (2 bits) 2.55s (51 bits) 42.4s (848 bits) ICX204AK HD V1 V2A/V2B V3 Sensor Readout Clock Timing Chart High Frame Rate Readout Mode XV1 XV2A/XV2B XV3 XSG1 XSG2 Sensor readout clock XSG1 is used by composing XV2A. - 16 - 0.1s (2 bits) 42.4s (848 bits) 2.55s (51 bits) 5.0s (100 bits) HD 2.7s (54 bits) V1 V2A V2B V3 10 bits ICX204AK 8 bits Drive Timing Chart (Vertical Sync) Progressive Scan Mode VD HD 9 10 792 1 V1 V2A V2B V3 788 790 779 CCD OUT 1 23456 71234 792 1 1 23 45 67 12 3 - 17 - ICX204AK Drive Timing Chart (Vertical Sync) High Frame Rate Readout Mode FLD VD BLK HD 5 15 525 1 10 20 520 265 275 V1 7 10 13 16 19 22 25 28 31 CCD OUT 757 760 763 766 769 772 Note) Vertical OB and aperture lines 1, 4, 775 and 778 are not output. 757 760 763 766 769 772 7 10 13 16 19 22 25 28 31 - 18 - V2A V2B V3 260 262 270 280 285 ICX204AK Drive Timing Chart (Horizontal Sync) Progressive Scan Mode HD 94 238 29 1 241 1 209 164 1 246 BLK 1270 1 45 CLK 1 45 1 RG SHP SHD 100 1 40 1 1 40 1 1 80 1 60 80 1 24 80 44 64 44 1 V1 1 - 19 - 1 60 2.0s 48 1 V2A 1 V2B V3 1 H1 H2 56 SUB 1 Note) 1 unit: 50ns ICX204AK Drive Timing Chart (Horizontal Sync) High Frame Rate Readout Mode HD 94 209 164 1 29 1 238 246 241 1 BLK 1270 1 45 CLK 1 45 1 RG SHP SHD 28 1 1 1 1 1 1 28 1 26 1 1 18 1 26 28 1 26 1 26 26 28 1 10 28 1 28 1 26 1 1 26 20 26 28 1 28 1 26 1 26 1 28 20 1 28 1 28 1 V1 1 10 V2A - 20 - 1 64 44 1 1 10 V2B V3 1 H1 H2 56 SUB 1 Note) 1unit: 50ns ICX204AK ICX204AK Notes on Handling 1) Static charge prevention CCD image sensors are easily damaged by static discharge. Before handling be sure to take the following protective measures. a) Either handle bare handed or use non-chargeable gloves, clothes or material. Also use conductive shoes. b) When handling directly use an earth band. c) Install a conductive mat on the floor or working table to prevent the generation of static electricity. d) Ionized air is recommended for discharge when handling CCD image sensor. e) For the shipment of mounted substrates, use boxes treated for the prevention of static charges. 2) Soldering a) Make sure the package temperature does not exceed 80C. b) Solder dipping in a mounting furnace causes damage to the glass and other defects. Use a ground 30W soldering iron and solder each pin in less than 2 seconds. For repairs and remount, cool sufficiently. c) To dismount an image sensor, do not use a solder suction equipment. When using an electric desoldering tool, use a thermal controller of the zero cross On/Off type and connect it to ground. 3) Dust and dirt protection Image sensors are packed and delivered by taking care of protecting its glass plates from harmful dust and dirt. Clean glass plates with the following operation as required, and use them. a) Perform all assembly operations in a clean room (class 1000 or less). b) Do not either touch glass plates by hand or have any object come in contact with glass surfaces. Should dirt stick to a glass surface, blow it off with an air blower. (For dirt stuck through static electricity ionized air is recommended.) c) Clean with a cotton bud and ethyl alcohol if the grease stained. Be careful not to scratch the glass. d) Keep in a case to protect from dust and dirt. To prevent dew condensation, preheat or precool when moving to a room with great temperature differences. e) When a protective tape is applied before shipping, just before use remove the tape applied for electrostatic protection. Do not reuse the tape. 4) Installing (attaching) a) Remain within the following limits when applying a static load to the package. Do not apply any load more than 0.7mm inside the outer perimeter of the glass portion, and do not apply any load or impact to limited portions. (This may cause cracks in the package.) Cover glass 50N Plastic package Compressive strength 50N 1.2Nm Torsional strength b) If a load is applied to the entire surface by a hard component, bending stress may be generated and the package may fracture, etc., depending on the flatness of the bottom of the package. Therefore, for installation, use either an elastic load, such as a spring plate, or an adhesive. - 21 - ICX204AK c) The adhesive may cause the marking on the rear surface to disappear, especially in case the regulated voltage value is indicated on the rear surface. Therefore, the adhesive should not be applied to this area, and indicated values should be transferred to the other locations as a precaution. d) The notch of the package is used for directional index, and that can not be used for reference of fixing. In addition, the cover glass and seal resin may overlap with the notch of the package. e) If the lead bend repeatedly and the metal, etc., clash or rub against the package, the dust may be generated by the fragments of resin. f) Acrylate anaerobic adhesives are generally used to attach CCD image sensors. In addition, cyanoacrylate instantaneous adhesives are sometimes used jointly with acrylate anaerobic adhesives. (reference) 5) Others a) Do not expose to strong light (sun rays) for long periods, color filters will be discolored. When high luminance objects are imaged with the exposure level control by electronic-iris, the luminance of the image-plane may become excessive and discolor of the color filter will possibly be accelerated. In such a case, it is advisable that taking-lens with the automatic-iris and closing of the shutter during the power-off mode should be properly arranged. For continuous using under cruel condition exceeding the normal using condition, consult our company. b) Exposure to high temperature or humidity will affect the characteristics. Accordingly avoid storage or usage in such conditions. c) The brown stain may be seen on the bottom or side of the package. But this does not affect the CCD characteristics. - 22 - Package Outline Unit: mm 16pin DIP (450mil) A 0 to 9 6.1 9 16 D ~ 2.5 C 11.43 8.4 5.7 V H 9.5 11.4 0.1 2.5 2-R0.5 1. "A" is the center of the effective image area. 2. The two points "B" of the package are the horizontal reference. The point "B'" of the package is the vertical reference. 3. The bottom "C" of the package, and the top of the cover glass "D" are the height reference. 4. The center of the effective image area relative to "B" and "B'" is (H, V) = (6.1, 5.7) 0.15mm. 5. The rotation angle of the effective image area relative to H and V is 1. 6. The height from the bottom "C" to the effective image area is 1.41 0.10mm. The height from the top of the cover glass "D" to the effective image area is 1.94 0.15mm. 7. The tilt of the effective image area relative to the bottom "C" is less than 50m. The tilt of the effective image area relative to the top "D" of the cover glass is less than 50m. 8. The thickness of the cover glass is 0.75mm, and the refractive index is 1.5. 9. The notches on the bottom of the package are used only for directional index, they must not be used for reference of fixing. ICX204AK B ~ 2.5 0.5 B' 0.69 1.27 0.46 0.3 M 0.3 PACKAGE STRUCTURE PACKAGE MATERIAL Plastic LEAD TREATMENT GOLD PLATING LEAD MATERIAL 42 ALLOY PACKAGE WEIGHT 0.9g 1.27 3.5 0.3 (For the first pin only) 3.1 - 23 - ~ 1.2 3.35 0.15 9.2 2.5 0.25 1.2 10.3 12.2 0.1 11.6 8 1 |
Price & Availability of ICX204
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |